Category Archives: Uncategorized

Easter, Heat and Wild Horses

Progress has been pretty slow on our new digs. Donna’s been organizing drawers, cabinets and closet space. I haven’t accomplished much. I’m still a little frustrated at times by looking for something, then realizing we left it in the motorhome – things like the extra wide foil for the Traeger and grill or the BBQ tongs. Yesterday I could have used a needle file. After searching, I realized my needle files were still in a cabinet in the coach.

Today I’ll go over to the 202 RV Valet storage facility and retrieve a couple of things. I also want to put mineral oil in the drains to seal the “P” traps. Water usually does the job, but since we aren’t running water down the drains, it’ll evaporate and allow odors from the holding tank to enter the coach. Mineral oil won’t hurt anything and won’t evaporate. I have a gallon of food-grade mineral oil I recently bought to condition our cutting boards.

On Easter Sunday, we went to Frank and Kelly Burk’s house for a late lunch/early dinner party. I think we had as many as 10 people there at one point with eight staying to eat. Kelly made traditional Easter food – ham and asparagus with hollandaise sauce and scalloped potatoes. Someone else contributed sweet potatoes made with a unique recipe that involved basting with 7Up and cooking for hours. Donna made a fruit salad and I made a slaw.

The slaw was interesting. It was very simple – just cucumber, a Granny Smith apple, a honey crisp apple and scallions. The dressing was apple cider vinegar, honey, sour cream, salt and pepper. The trick to making this slaw is to slice the ingredients extremely thin. I sliced the cucumber and apples into 1 to 2mm thick slices – a thickness somewhere between dime and a quarter thick. Kelly was surprised that I did this with a knife, not a mandolin or some other slicer.

I’ve been working on my kitchen cutlery skills and I sliced these ingredients with a technique that’s probably old-hat to the cooks out there reading this, but it’s fairly new to me. I held the food items on a cutting board with my left hand with a claw grip. I curled my fingers back toward my palm, keeping my finger tips away from the knife blade. The side of the knife blade butts up against the second joint of my middle finger. With each slice I move my grip slightly before slicing again, creating the thin, uniform slices.

Claw grip on a cucumber

With the cucumber, I sliced it lengthwise first, leaving about half an inch still attached at the stem end. Holding it in a claw grip with the slice vertical, I made thin slices that were half the diameter of the cucumber. I used my FKRZ bunka Japanese kitchen knife which has a blade about 2 inches tall, giving me a lot of surface against my finger joint with no danger of slicing my finger tips.

The dinner, conversation and company was much fun and we really enjoyed the Easter gathering.

On Monday afternoon, we invited Dick and Roxy Zarowny for happy hour. They were pulling out of Viewpoint Golf and RV Resort on Tuesday morning to head back home to Spokane, Washington. Donna made baked jalapeno poppers and a bean dip for tortilla chips. Donna and Roxy had kayaked on the Salt River the previous Thursday and hoped to see wild horses. They had fun, but didn’t see any horses – Roxy’s been skunked on wild horse sightings.

One of the things slowing me down on household projects is pickleball. I’ve played almost every day this week. A couple of hours on the court with full sun and temperature in the 80s really wears me out. Today was the fifth day in a row on the court and my legs are weary.

I mentioned the Japanese bunka knife. I want to talk about a Japanese knife blacksmith. His name is Teruyasu Fujiwara (knife nerds refer to him as TF). He is a fourth generation Japanese blacksmith and is known for his heat treatment of Hitachi YSS high carbon steels – shirogami #1 (white #1) and aogami super (AS). In the 1970s, he and his father pioneered the technique of forge-welding stainless steel and carbon steel in to a san-mai (three layer) laminate. This allowed them to heat treat the core carbon steel to a high hardness level while taking advantage of the superior corrosion resistance and toughness of mild stainless steel.

When they started experimenting, they thought they would probably encounter a 20% failure rate – the laminations would de-laminate or crack during heat treatment. They actually lost 80% of their work before they perfected the process. Since then, Hitachi Steel Corporation’s YSS specialty department has developed a process for producing laminated san-mai steel in sheet form.

TF is one of only a handful of blacksmiths that can successfully forge weld their own san-mai stainless-carbon sandwich steel. He claims the hand forged san-mai to be superior to the machine rolled pre-laminated factory stuff. He makes three lines of knives. The first, entry level to TF knives is called the Nashiji line. This is “value” priced and made from pre-laminated factory rolled san-mai steel with a white #1 core and soft stainless cladding. His heat treatment of this steel results in a high hardness level allowing exceedingly sharp edges while paradoxically being easy to sharpen. “Value” pricing is relative – non-knife nerds would probably think these are expensive knives.

The next level of his knives are the Maboroshi no Meito – Maboroshi or Mabs is the common reference name. These are white #1 core with soft stainless cladding hand forge-welded by TF. These achieve an even higher level of hardness and retain the ease of sharpening. These knives have legendary cutting ability, but they cost double the price of a Nashiji knife.

His top level is called Denka no Hoto – Denka for short. Denkas are made with Aogami Super cores and soft stainless cladding hand forge-welded by TF. Once again, the price is double that of the Maboroshi, making them very pricey! The AS steel reaches a super hard level – 67HRC or so and features a razor thin edge that holds up well. I doubt I’ll ever buy a knife in this price range.

I have a few TF Nashiji level knives and I’m really impressed by them. I’m so impressed that I felt I had to try a Maboroshi to feel that hand forge-welded magic I keep hearing about. I ordered one from District Cutlery in Washington D.C. and received it yesterday. I haven’t used it yet, but it came scary sharp!

Teruyasu Fujiwara Maboroshi gyuto (Japanese chef’s knife)
TF Mabs top with Nashiji bunka and 160mm and 135mm petty’s below

I like the finger cut-out in the choil (rear of blade) in the Maboroshi. It makes a very comfortable pinch grip.

Yesterday, Donna went kayaking on the Salt River again, this time with Kelly Burk. They put in at Goldfield and kayaked about two and a half hours downriver to Granite Reef. They saw nine wild horses this time. Maybe Roxy will see them next year!

Wild horses on the Salt River

We had a few interesting meals this week. On Saturday, Donna pan-seared ahi tuna and served it with jalapeno, ginger and lime sauce over white rice, with quartered cucumbers and avocado.

Pan-seared ahi plate

On Tuesday, Donna made spicy-sweet grilled chicken with dijon mustard sauce and served it with rice and grilled broccolini.

Spicy-sweet grilled chicken with dijon mustard sauce

Yesterday, I fired up the Traeger wood-pellet fired smoker-grill and put on a rack of babyback ribs I’d prepped the day before. These are always a favorite. No picture this time – I’ve photographed the entire process a few times on these blog pages.

The weather has been very warm with the hottest day of the week on Easter Sunday – we hit 98 degrees. Every day has been in the lower 90s. We expected cooler temperatures by now, but it looks like we’ll have a couple more 90 degree days before the temperature drops into the 80s on Sunday and low 80s by Wednesday. With the sun rising earlier and warm mornings, we’ve been up earlier.

Tuesday morning I woke up around 5am and couldn’t get back to sleep, so I got up and watched the sunrise over the Superstition Mountains to the east.

Sun rising behind the Superstition Mountains

Most mornings lately we’re out of bed by 6:30am and off to pickleball around 8am. On Monday, Wednesday, Friday and sometimes Saturday, Donna plays tennis from 9am to 10:30am. We’ve been running the air conditioner here in the afternoon and the swamp cooler in the Arizona room, but I’m having doubts about the effectiveness of the swamp cooler. I’ll have to look into it.

*Just so you know, if you use this link to shop on Amazon and decide to purchase anything, you pay the same price as usual and  I’ll earn a few pennies for the referral. It’ll go into the beer fund. Thanks!

Transition

It has been a busy week since my last post. Over the weekend we put the Nissan Frontier to good use hauling numerous loads of stuff out of the motorhome to our new-to-us park model home. It’s amazing how much stuff we’d been hauling around the country. Over time, it’s easy to forget about some of the items buried deep in the basement compartments of our motorhome.

The home we bought came fully furnished – including things like kitchen utensils, pots and pans, silverware and plates. This made it harder to decide what we needed to move from the coach and also where to put everything. It’s an ongoing process – I keep searching for things as Donna reshuffles storage. Something I found in one cabinet yesterday is now in a different location. She’ll refine her organization of stuff soon and I’ll learn where to find things.

We spent our first night here on Sunday. It was an adjustment. After nearly eight years in the coach with only a few exceptions, it felt strange. On Monday morning, I had an appointment at Cliff’s Welding to have the Roadmaster base plate installed on the Frontier. It took longer than I expected – I didn’t get out of there until 1pm. The truck is set to be towed behind the coach when we depart from here.

Tuesday we got what should be the last load of stuff out of the coach. I drove the coach over to 202 RV Valet for storage, Donna followed in the Frontier. This RV storage facility is new – I think it’s less than two years old. It’s owned by the same people that own RV Renovators where we had extensive work performed a few years ago.

The coach is in a covered space, but it will get partial afternoon sun. I covered the tires to mitigate UV degradation. The space also has a 20-amp service – adequate for the batteries to maintain a charge. Of course, when I went to hook up to the electrical outlet, I realized my 20-amp adapter was in a box of stuff I moved to the shed at our new place. Not a big deal though, the storage yard is less than two miles from Viewpoint Golf and RV Resort and we have 24/7 access.

As we slowly settle in, we’ve been taking time to enjoy the back deck, watching golfers – and occasionally watching out for errant golf balls – and enjoying the view and weather.

Our back deck viewed from the 6th fairway of the golf course
View to the north – 6th green and 7th tee
Late afternoon view from the deck to the southwest

We also have a nice view to the east from the front room and side deck at our entry. We look down the 1600 Lane of the park at the Superstition Mountains.

Superstition Mountains in the background

We’re liking the transition into a more conventional dwelling, but we’ll still be hitting the road. Our tentative plan at this point is to leave Mesa, Arizona by May 10th. This date was predicated on the billing policy at 202 RV Valet. If you take your rig out of storage by the 10th of the month, they pro-rate the monthly fee. If you move out after the 10th, you have to pay for the entire month. I don’t like the policy, but it is what it is. It’s not like they would lose money if you left on the 11th or later – they told me they have a waiting list of more than 140 people!

We haven’t made a plan for our exit from the Valley of the Sun at this point. Presumably we’ll head north to a cooler climate, but we don’t really know where we’re going.

Did I mention the new place included a barbeque grill? It’s a large CharBroil grill with four burners, a large grilling surface and also a side burner suitable for a pot or pan.

CharBroil grill

Yesterday, Donna marinated a pork tenderloin with her mojo marinade and I grilled it on our new-to-us grill. This was the second time I’ve used the grill and I’m getting used to the settings I prefer. A new grill always takes some time to learn its adjustments for fine tuning temperature settings. I’m not used to grilling on such a large grill. When we were in our sticks-and-bricks home, I had a large Weber gas grill, but it’s been eight years since I’ve manned that.

Lots of grill-estate

The tenderloin came out fine.

Mojo marinated pork tenderloin

Donna roasted cauliflower in the oven – yeah we have a kitchen with a real oven and stove.

Dinner is served

The weather has been pretty much as predicted – on the very warm side. The week started with mid to upper 80s. By Thursday, we were in the low 90s. Yesterday we hit 93 degrees and the forecast calls for the same today. After a couple more hot days, they say we can expect to return to the low 80s for most of April.

*Just so you know, if you use this link to shop on Amazon and decide to purchase anything, you pay the same price as usual and  I’ll earn a few pennies for the referral. It’ll go into the beer fund. Thanks!

Trailer For Sale – Sold

I mentioned another project that needed attention in my last post. Our 10-gallon Suburban water heater isn’t working right. This unit operates on 120-volts AC or propane. When we’re on a 50-amp electrical service, we keep the water heater on electric power.

Apparently, the electric heating element is going bad. It won’t heat the water adequately – we only get lukewarm water – I doubt if it’s much over 100 degrees. We have to turn on the propane gas burner to get hot enough water to shower or wash dishes.

I found a tune-up kit for the Suburban SW10DE water heater that included the heating element online at PDX RV. It also had a replacement thermostat set at 130 degrees. The kit was only $33, but shipping was $15!

I found a heating element wrench at Ace Hardware for $10. This is a thin wall, stamped sheet socket, 1-1/2 inches in diameter. The heating element has a thin 1-1/2 inch hex on top of the threaded portion of the element.

Heating element socket

With the proper tool and parts in hand, I got to work. I made a “curtain” out of a plastic grocery bag to keep any sediment that might come out of the tank off of the coach. The heating element had a plastic cover over it and it was behind the gas tube, so I had to remove the gas tube and cover for access.

Heating element exposed

I had turned the circuit breaker for the water heater off, then I removed the two wires from the element. I used the socket tool, but I found the element threads were stuck in place. I worked on it for about 45 minutes before I decided I needed to try something different. I found a 1-1/2″ standard socket at the auto parts store. I figured I could use my 1/2-inch drive electric impact driver to break the element loose.

The thin hex on the element didn’t allow the socket to fully engage the hex and the impact driver just rounded the tops of the hex corners. Next I soaked it in penetrating oil and let it stand overnight. I found a bar about two feet long that I could use as a breaker bar on the heating element tool for leverage.

I huffed and puffed and gave a mighty pull on the cheater bar and promptly bent the heating element tool without budging the element. The threads remained frozen in place. At that point, I threw in the towel and put it all back together. I’ll have to hire an RV service that either has a better tool or a better idea to get the old element out. I hate to give up, but sometimes you have to admit defeat.

Donna has been busy getting the park model home ready for us to move in. Last Saturday Viewpoint Golf and RV Resort had a community patio sale. Many of the homes here in the park put out items for sale. Donna had a lot of stuff she wanted to get out of the house before we move in. She sold quite a few items. The things that didn’t sell we took to Goodwill.

Donna’s patio sale

She’s been working on replacing window coverings with help from our friends, Roxy and Dick Zarowny. They also did some paint touch up. Roxy repainted a cabinet, changing the white finish to gray.

The RV park is slowly emptying out as snowbirds return home. Our friends Chuck and Sue Lines left last week to head back to Illinois. We have about a dozen empty sites in front of our coach and only three RVs in sight.

I ordered set of coarse (400 grit) and medium (1000 grit) diamond sharpening stones and had another go at Roxy’s LC Germain kitchen knives. These stones were aggressive and worked better on this steel than the fine synthetic Japanese water stones I used before. They left a toothy finish that I refined a bit on a medium Spyderco Sharpmaker stick. The result was an acceptable level of sharpness that remained on the toothy side. A toothy edge is good for cutting most proteins or things like thick-skinned tomatoes. A more refined edge is needed to make clean cuts of fish. I think her knives will work better now.

By Wednesday, I had almost everything out of the trailer and needed to advertise it for sale. I was a little worried as I had to have it out of here on the 30th of March – only six days away. Donna wrote up an ad and posted it on Facebook Marketplace Wednesday evening. She had immediate responses! I had searched online to find comparable trailers to set a price and had a hard time finding anything. The closest I could find were either beat-up and selling for cheap or they were really high-end models – I only found a few examples and nothing really matched our trailer.

I told Donna what I expected to get for the trailer and soon found out I under-priced it. We had people lining up to buy it and a bidding war broke out. I sold it for $700 over my asking price and the guy came Thursday morning from Casa Grande to buy it. He paid cash and left with a smile on his face. I thought the lack of trailers this size online indicated a lack of interest – most of the trailers were around the 12-foot length. It turns out there’s low supply and much demand for larger trailers. I probably could have sold for a higher price, but I’m satisfied with how things turned out.

We’ll be moving into our new place over the weekend. On Tuesday, I’ll take the motorhome to a new storage facility that opened on Main Street near the Loop 202. I’ll have it under a covered space there. I think we’ll hang around here until mid-May unless it gets too hot earlier. We don’t have a real plan for the summer yet – we just know we want to leave before the temperatures are in triple digits.

The weather for the past week had been fickle. We’ve had warm, sunny days with the high temperature ranging from the mid-70s to mid-80s broken up by a few cooler days with wind and rain showers in the 60s. It’s cool today with a predicted high of 62 degrees, but we’ll warm up to the 80s over the weekend and may hit the 90s by the end of the week.

*Just so you know, if you use this link to shop on Amazon and decide to purchase anything, you pay the same price as usual and  I’ll earn a few pennies for the referral. It’ll go into the beer fund. Thanks!

It’s Not If, It’s When

We’ve been busy here at Viewpoint Golf and RV Resort. The painter we hired, Gary, started working on prepping the interior of our new-to-us park model home last Friday. He sprayed the interior, including the ceiling in the all of the interior except for the Arizona room addition. He finished spraying on Tuesday and on Wednesday did some touch-up and clean-up.

Saturday morning we played in the annual pickleball tournament. Donna and I teamed up in the 3.0-3.5 group and had a good time. Went 3-3 but all of the games were close. I really don’t mind losing a game if we’re competitive and put up at least eight or nine points.

Wednesday was St. Patrick’s Day and we had corned beef in two slow cookers. I had trimmed the corned beef early in the morning and Donna got them started by 8:30am. I sliced cabbage and potatoes later. Donna had Irish soda bread in the oven in the afternoon. At 4pm, we transferred everything to our new place.

Our friends Chuck and Sue Lines and Dick and Roxy Zarowny joined us on the rear deck for a St. Patrick’s Day dinner. It was pleasant outside, mostly blue skies and the temperature was in the low 70s with very light wind. I was surprised to find the golf course empty. We enjoyed the company and had lots of conversation to go with our meal. Sue brought glazed carrots and Roxy contributed key lime pie for dessert.

We broke up the dinner party early – around 7:30pm. Chuck and Sue had an early morning on Thursday as they were pulling out with their fifth-wheel trailer to head back to Illinois. I was enjoying myself and relaxing so much, I failed to take any photos!

Donna has been busy taking stuff out of the coach basement storage areas – some things we haven’t used in a long time, but we wanted to keep. Now we won’t have to carry everything we own around with us – some things will remain here at the house.

While she was cleaning out one of the bins, she noticed a wet area. There was a very slow drip coming from the inlet to the electric water pump for the fresh water tank. I crawled under to have a look. Getting into the compartment, I banged my head on the door latch. I had to twist a bit to see the source of the leak. It was the filter – really just a metal mesh strainer with a plastic housing – on the pump inlet.

The small cut on my head was bleeding – even small head wounds can bled profusely. Twisting and turning my head while I was stretched out in the compartment caused the blood to run across my forehead and down my nose. I got out and walked to the door of the coach. Donna and Roxy were outside talking. When they looked at me they thought I had been wrestling in a WWE event – blood was running all over my face. It was a minor cut really and I was able to stop the bleeding quickly with a wet paper towel compress.

I put an oil drain pan under the drip – it holds a couple of gallons – and went online to find a new strainer. I ordered one from Amazon that would arrive the next day. While I was checking the leak out, I thought about the spare water pump I had. About six years ago we were in San Diego when I saw another Alpine Coach. The owner was busy repairing a water leak. I asked him what was up. He told me his water pump was leaking and had to be replaced.

He said it was a common issue with the RV Aquajet pump used in Alpine Coaches. He advised me to order a Shurflo 4008 RV Revolution replacement pump to have on hand. His words were, “It’s not if, but when your Aquajet starts leaking.”

Amazon delivered the replacement strainer on Wednesday as promised. I got back into the compartment to compare the part and see what it was going to take to install it. I was shocked to see we no longer had a slow drip – it went from a drop every 10 seconds or so to a steady drip, drip, drip and it was coming from the bottom of the water pump. The Aquajet pump failed. Now I was glad I had carried a replacement to have on hand for the last six years!

Aquajet pump leaking – line already disconnected from output side

I drained our fresh water tank and removed the old pump. The Aquajet and the new Shurflo are different designs with different dimensions. Luckily, the new strainer I got from Amazon was a direct fit on the Shurflo.

New pump and old pump – different dimensions on the mounting brackets

The mounting brackets were different, but I could see they would fit on either pump with just two screws. Rather than drill new mounting holes in the coach, I swapped the mounting bracket so I could use the existing holes and original bracket on the Shurflo.

When I got the pump mounted, I had another problem. Due to the different dimensions of the pumps, the water line from the fresh water tank to the inlet strainer was now an inch short. I needed 39 inches of water line and it was only 38 inches. I pulled the old line and rummaged around in the trailer. I found a 44-inch length of 1/2″ pex tubing. Perfect. I cut it to size and was back in business.

Shurflo installed and ready to go

After assembling it all, I turned the water supply back on and checked for leaks and found none. I filled the fresh water tank about a quarter full and ran the pump. No leaks, good flow and pressure. The new pump is much quieter than the old Aquajet – it’s nearly silent. Job done!

I have another project that’s taking valuable time from our move effort. The electric heating element on our Suburban 10-gallon water heater in the coach is going out. It doesn’t bring the hot water up past lukewarm. We have to run it on propane to get hot water. That project will be fodder for another post.

I’m continuing to work on my kitchen skills. On Monday, I made miso soup. So what, you say. Well, I didn’t make it from a package – I made it from scratch. That meant I had to make dashi first. Dashi is a Japanese broth that’s the base for a lot of Japanese recipes, including miso soup. I made awase-style dashi which is flavored by boiling dried kelp, then adding bonito flakes as it cools. After straining it, you have dashi.

The miso soup had yellow miso, tofu cubes, dried king black (shiitake) mushrooms and chopped scallions. It was good, but I needed to do a better job of reconstituting the dried mushrooms. I served it as an appetizer while Donna made a proper dinner plate.

She made pan seared scallops with lemon-caper sauce and steamed asparagus on the side.

Pan seared scallops with lemon-caper sauce

This was a delicious meal – every bit as tasty as the fancy recipe looks.

The weather has been a little crazy over the last week. We had rain showers Friday and again on Saturday afternoon and the thermometer struggled to top 60 degrees both days. By Monday, we had low 70s but dipped down to 60 again on Tuesday. As already mentioned, St. Patrick’s Day was fine with mid 70s and we hit 83 degrees yesterday. Today’s forecast calls for 80s again before dropping back into the 70s for the coming week.

*Just so you know, if you use this link to shop on Amazon and decide to purchase anything, you pay the same price as usual and  I’ll earn a few pennies for the referral. It’ll go into the beer fund. Thanks!

Pre-Move Activities

Things are progressing slowly with the new-to-us park model home here at Viewpoint Golf and RV Resort. So far, the process has been a matter of removal rather than move-in. Donna has been sorting through the things she plans to sell in the park-wide garage sale scheduled for Saturday, March 20th. Whatever doesn’t sell will be donated.

Donna also took down all of the window hangings – curtains, rods and whatnot. They were all dated and in need of replacement. I hauled it to the community dump here at the park. There was also a small knick-knack shelf that ran around the perimeter of the living room that she didn’t want. She hired a guy from the park to rip it out and dispose of it along with a cabinet above the bed.

We’ve had some great help from our friends and neighbors, Dick and Roxy Zarowny. Roxy has been helping Donna with some paint prep and color ideas. Dick took down a few light fixtures we’ll be replacing and he also filled in trim where the living room shelf was. Another neighbor, Sue Lines, has also been consulted about paint colors. We can’t thank them enough for their time and help.

I’ve moved a few items into the small shed/shop. I’ll need to get cracking on moving everything out of the trailer so we can sell it. That’ll be this weekend’s project. Yesterday, I went over to the house to spackle some holes left from curtain hardware and other wall hangings.

Spackle job around garden window

We had a change of plan on painting the interior. We got a quote from a painter here at the park and decided to hire the job out. In years past, I always tackled these jobs to avoid the expense of hiring someone, but I’m at a point in my life where I’d rather hire someone and be done with it. They will start masking everything and apply coverings tomorrow and should complete the job by the middle of next week – they won’t work on the weekend. Once that’s complete, we can start moving in.

I’ve mentioned a bit of an evolution in my kitchen duties – I’m learning kitchen knife skills and applying them to different recipes. Meanwhile, Donna has been utilizing the Weber grill more. One of my specialties is Japanese fried rice. I’ve been making it in a large skillet, but it wasn’t ideal. The skillet isn’t quite large enough and stirring while the rice fries results some of the ingredients escaping from the pan.

I decided I needed a wok. I looked around online and settled on a Yosukata carbon steel wok from Amazon. It has a flat spot on the bottom making it stable on the induction cooktop and carbon steel is ferrous and works great with induction. The name “carbon steel” is a misnomer. All steel contains iron and carbon.

After ordering this pan, I’ve been inundated with ads and click-bait for carbon steel kitchenware. Against my better judgement, I clicked on one that led to blog post about cookware – it was just a shill for certain products. The author was either horribly mis-informed or didn’t do any research at all. He started by saying carbon steel is great in the kitchen because it is a blend of “normal steel” and stainless steel. This is preposterous. First of all, what is “normal steel?”

As I said, all steel contains iron and carbon. From there, different alloying elements can be added. Most metallurgists agree that the addition of chromium in amounts exceeding 11% of the total weight constitute a stainless steel alloy. So-called carbon steel can be anything from very pure iron and carbon like that found in Hitachi Shirogami steel or can have additions like manganese, tungsten, vanadium and a host of other ingredients – but it wouldn’t be called carbon steel if it had more than 11% chromium – it would be called stainless. This is why I say the statement in the kitchen blog is preposterous.

Anyway, the wok is carbon steel and when properly seasoned – like cast iron – it’s nearly non-stick in use. The pan is made from thin material that heats up and cools down quickly and is much lighter than cast iron. It’s sizable – nearly 14 inches in diameter and four inches deep. Just right for fried rice.

Carbon steel wok and fried rice

Speaking of steel, Roxy mentioned to Donna that her old set of kitchen knives she keeps in their motorhome were in need of sharpening. So Donna asked me if I could sharpen them for her. It was a set of LC Germain knives. These knives were made in Japan in the 1970s and ’80s. They are stamped from a sheet of stainless steel and achieve their sharpness through the use of very thin blade material. To make the thin blades wear-resistant, they were heat-treated in a way that forms large, very hard carbides. I think the manufacturer wanted these knives to hold up in home kitchens where the user wouldn’t sharpen them or would maybe send them out to be sharpened by someone with a grinder once a year or so.

I don’t have a grinder and my Japanese knives are carbon steel with very fine grain structure, making them easy to sharpen. Therefore, my Japanese water stones are finer grades. These LC Germain knives should have been sharpened with a coarse stone to reset the edge, then refined on harder stones. I couldn’t find my Lansky coarse stone, so I had to use the Spyderco Sharpmaker which I only have medium and fine grit stones for. It took a lot of elbow grease to reach a useable edge on the knives. Hopefully, I’ll find the Lansky sharpener when I empty the trailer and can have another go at the LC Germain knives.

We drove out to Buckeye on Sunday to visit with my middle daughter, Jamie. Jamie is starting a home baking business specializing in cookies – it’s called OMG Cookies. Donna ordered two dozen cookies from her that she wanted for gifts to her tennis girlfriends here at Viewpoint. I gifted Jamie with the Yaxell Enso Japanese ko-bunka knife that got me started on the Japanese knife kick. We visited for a while, then made the drive back – it’s about 75 miles each way. In the air-conditioned Nissan Frontier, the trip was breeze.

The Frontier airbag saga continued. I was up early and off to the Nissan dealer in west Mesa to have the airbag module replaced and programmed on Monday. I waited there for four hours – good thing I brought a book to read. It didn’t solve the problem. They said the wiring harness needed to be replaced and said Sullivan Motors would be calling me to make arrangements.

Chris at Sullivan called me on Tuesday and said he was working on a solution. Then he called on Wednesday and asked if I could bring the truck to their shop at 8am on Thursday (today). He said the wiring harness was on backorder, but he thought they could repair it. I was skeptical , but I got up early and went there this morning. He had a different guy look at it this time. I sat and read for a while, then took a walk. When I got back, the truck was parked outside the shop. The guy located the break in the harness and repaired it! Hopefully, that’s the last time I’ll have to deal with it.

Time for some food talk. The fried rice in the wok photo went with a wild Alaskan salmon filet that Donna grilled perfectly.

Wild Alaskan salmon with mayo-based seasoning and grilled shishito peppers

I’ll add a couple more dinner plates from the last week. Donna made balsamic chicken and peppers served with home fries.

Balsamic chicken with peppers and home fries

She also made a meal with leftover tri-tip from the weekend. She had me slice the tri-tip into thin slices along with mushrooms, onion and garlic. Then she cooked chickpea rotini pasta and made a version of classic beef stroganoff.

Tri-tip steak beef stroganoff

It was a delicious meal.

We’re looking forward to visit from my oldest daughter, Alana and her fiancé, Kevin this afternoon. We’ve had warm weather over the weekend and start of this week – it was in the 80s. Yesterday it cooled down and only reached 70 and today should be slightly cooler. It should be comfortable to sit outside in the sun while we catch up with them.

*Just so you know, if you use this link to shop on Amazon and decide to purchase anything, you pay the same price as usual and  I’ll earn a few pennies for the referral. It’ll go into the beer fund. Thanks!

Not As Planned

Another week has gone by and I haven’t written a post. Things didn’t always go as planned this last week. I mentioned in my last post that I had to take our Nissan Frontier back to Sullivan Motors for a repair to the airbag system. I got up at 6am on Friday for coffee and breakfast before heading out at 7:15am.

They were going to change the clockspring for the airbag and said it would take all day. I didn’t understand this – I’ve never done this job on a Nissan, but I changed out six clocksprings in a day on Volkswagens. We had a quality engineer that wanted airbag clocksprings with various time/mileage for study. He sent me six new parts. I went to an auction yard in Avondale, Arizona where I found used Volkswagens and removed and replaced the clocksprings which I tagged with VIN and mileage and shipped them to the engineer. But, I digress.

I saw them take the truck into the shop right at 8am. Donna came about half an hour later to pick me up in Midget-San. We came home and I hit the pickleball courts. I took a phone call at 10am – it was Sullivan Motors. They guy told me he had bad news. The clockspring didn’t fix the problem so they ordered a control module. It’s an expensive part, but it’s on them as the airbag repair was part of the sales agreement. I’ll have to bring the truck to the Nissan dealer when they get the part – it requires programming by the dealer.

I told Donna I was a little worried about having the truck diagnosed by a parts replacer. Donna asked me what I meant by that. A parts replacer is a mechanic that lacks diagnostic skills – they read a fault code and jump to a conclusion without going through proper test procedures and just order the part they think will fix the problem. In my years with Volkswagen Technical Service, I ran into many examples of this. We’ll see if replacing the airbag control module was the right call.

Another plan that went awry was the title transfer for our new-to-us park model home. The seller wanted us to meet him at a third-party vehicle licensing place at 1pm on Monday. Donna and I arrived at the place right at 1pm. We saw a sign on the door that said service was by appointment only. Then we were told they used to do mobile home title transfers, but no longer do. They gave us the address and phone number of a place that does. I called the other outfit and the next appointment available was Wednesday morning at 10:30am. I made an appointment.

Then I called the Arizona Department of Transportation to see if they would be able to get us in. Their number went to a voice mail system that said call volumes are high, call back later – click! Typical service from a government agency.

Speaking of government agencies, I received the license plates from South Dakota for the Nissan Frontier. I looked at the registration reciept and saw they charged $460 excise tax. This was not right, because I paid Arizona sales tax when I bought the truck. South Dakota credits the sales tax for out-of-state vehicle purchases and only charges excise tax if the South Dakota tax is higher than the out-of-state tax – they charge the difference. I paid more than the South Dakota excise tax already, so the tax should have cancelled out.

I called the county treasurer office in Sioux Falls and they told me they had to get the documentation from the department of motor vehicles. This made no sense to me, I sent the documentation to the county treasurer as instructed, they should have records. They said they would call me back. The next afternoon I called them since no one called me back. I was told that the DMV records are being transferred to a new system and it would be weeks before they could retrieve them! I still had the documentation, so I sent it to the county again via email. I’m still waiting for a response.

Yesterday, we went to the third-party licensing place for our 10:30am appointment. What a disorganized zoo that was. It was 10:50am before we started the process and it took much longer than I expected. It was after 11:30am by the time we had everything signed and we were good to go. The park model home is officially ours.

Donna’s been sorting things out at the house – the sale included most of the stuff inside including furniture, appliances even kitchen utensils and linens. Donna will figure out what has to go before she starts moving our stuff in and getting it all organized. She also wants to paint before we move ourselves into the new house. That could take a few weeks.

Yesterday, while Donna was over at the house in the afternoon, I was puttering around in the trailer. It was breezy outside and wind gusts were picking up. Suddenly, great gusts of wind started rocking the trailer. I went out to check the canopy on the ham shack and it was whipping madly in the wind. I started removing the canvas but before I could take it all down the wind delivered a fatal blow. The ham shack canopy was destroyed.

Ham shack disaster

Luckily I wasn’t sitting at the table with my ham gear at the time! The wind carried dirt and desert sand. To the north I could see a haboob – a dust/sand storm that obscured Usery Mountain.

You can just make out Usery Mountain as the haboob begins to clear – how did that tent survive?

I’ll be setting up a new ham shack in the small shop area of our new home.

I’ll close this post with a shot of a dinner Donna made last week. It’s a Greek pork stew made with pork tenderloin, potatoes, kalamata olives, baby kale and white beans.

Greek pork stew

The weather has been great, other than the wind storm. Sunday was cool – in the mid-60s. Monday was warmer and by Wednesday we had mid-80s! Today is a little cooler but the forecast calls for low 80s through the weekend.

*Just so you know, if you use this link to shop on Amazon and decide to purchase anything, you pay the same price as usual and  I’ll earn a few pennies for the referral. It’ll go into the beer fund. Thanks!

Lost Dog

We’ve all been coping with the pandemic for nearly a year now. People have adjusted their lifestyles in different ways. For us, it mainly affected how we entertain. We’ve avoided large gatherings and only eat out or go to a pub when we can be seated outdoors. I think this is true for many people.

I browse a number of forums online and from what I gather, there’s been a resurgence of home cooking – this makes sense as restaurants are restricted in many areas. If you take a look at a couple of online kitchen knife retailers, like Japanese Knife Imports or Japanese Chef Knife, you’ll see more sold out items than knives on offer. We still manage to socialize and dine with friends – we just restrict the number of people we interact with.

Sunday was a great example. We went over to Frank and Kelly Burk’s house for a potluck-type meal and cocktails. Mike and Jodi Hall also came over. Mike brought shredded pork and beef he had smoked for tacos. We brought taco toppings, a green salad and tortillas. Kelly made flan for dessert – it was her first attempt at flan and it was outstanding.

Creamy Caramel Flan

As usual, we had a good time with great food, good people and lots of laughs.

I don’t have much to report as it’s been business as usual this week – pickleball in the mornings, a couple of grocery runs and playing with ham radio in the afternoon. We’ve been doing a lot of cooking, but that’s not unusual for us. What is a little different is our roles in making some of our dinners. For example, on Tuesday. Donna manned the grill and cooked chicken thighs, legs and wings while I was in the kitchen preparing Japanese fried rice. Donna also grilled baby bok choy. The grill used to be my bailiwick while Donna cooked in the kitchen.

Grilled chicken, bok choy and fried rice

We’ve been buying whole young chickens, right around five to six pounds. I break down the whole chicken into 10 major pieces – two legs, two thighs, two breasts, two tenders and two wings. I also set aside some of the other meat taken from the carcass to use for yakitori. We find the whole young birds to be more tender and flavorful than the over-sized breasts and other pre-cut chicken meat found in most grocery stores.

Since we had a lot of fried rice leftover, Donna decided on Wednesday night to make a new recipe – orange beef. She used boneless ribeye steak. I was her sous-chef – well, I was more like a line/prep cook. She told me she needed minced ginger, minced garlic, and minced jalapeno pepper and I got to work. She used these ingredients along with orange zest and orange juice, soy sauce and brown sugar to make a sauce. Meanwhile, I trimmed the thin-cut steaks and cut them into strips along with some green onions.

Orange beef with broccoli and fried rice

It was delicious – the orange beef is a winner.

A couple of rows down from our site, there’s a park model home that has informal live music occasionally. They keep it under the radar. They put a sign out with a picture of a dog – the sign says “Lost Dog.” That’s the signal for live music on that day. It also has a smaller sign that says “Band practice at XXpm.” The Lost Dog band usually plays in the evenings, but yesterday they were playing in the afternoon as I returned from giving pickleball lessons.

Lost Dog band

They have to keep it low-key because we aren’t really supposed to have gatherings with entertainment in the park under covid restrictions. Everyone has been good about it – keeping their distance and they keep the sessions short enough that a large crowd doesn’t gather.

We have four more days until we close the deal on our park model house. Here in Arizona, park model homes are classified as mobile homes – even though you’d have a hard time ever moving one. This means transfer of ownership isn’t like a regular real estate transaction – it’s more like titling and registering a car! I’ll withdraw a cashier’s check from the bank tomorrow and on Monday, we’ll go to the DMV and make the transaction.

The weather this week has been great as promised. We’ve had daily highs near or at 80 degrees. It will be a little cooler – in the lower 70s for the week ahead, but we should continue to have plenty of sunshine. Tomorrow I’ll have to be up early – I have to take the truck back to Sullivan Motors in west Mesa at 8am. The airbag light is on and they have to replace the clock spring under the steering wheel and a side curtain airbag. This was part of the deal when I bought the truck. It will probably take most of the day to perform the work.

*Just so you know, if you use this link to shop on Amazon and decide to purchase anything, you pay the same price as usual and  I’ll earn a few pennies for the referral. It’ll go into the beer fund. Thanks!

Sunshine On My Headlights

We had more good company this week. On Thursday, we met up with Deb and Jeff Spencer at Fat Willy’s for lunch on the patio. The last time we saw Deb and Jeff was in Kanab, Utah in September. We’ve met up with them several times over the years in various places – that’s how it often works with fellow full-timers.

Fat Willy’s is a pub/restaurant and also has the pro shop for the golf courses at Viewpoint Golf and RV Resort. As I mentioned, we took a table on the back patio overlooking part of the 18-hole course. I shot a photo of the view, but neglected to get a people photo.

View from Fat Willy’s

The photo above illustrates Arizona winter grass. The grassy areas surrounding the course appear to be Bermuda grass, which goes dormant over the winter. Bermuda grass goes dormant and doesn’t produce chlorophyll when the soil temperature drops into the 50s. It will recover in the spring with an application of fertilizer. The fairway is green – presumably it was overseeded for the winter with a rye grass variety. I don’t know what type of grass is used on the greens.

After a couple of hours of pickleball in the morning, I took care of a small project on Friday. Our new-to-us Nissan Frontier had some deterioration of the acrylic headlight covers. This has been a common problem for cars built with this type of headlight over the last 20 years – especially in areas with abundant sunshine. The acrylic covers are coated with a UV inhibitor, but over time, it breaks down – especially here in the desert.

Our Nissan Frontier was originally sold by Peoria Nissan on the west side of Phoenix and has been in the valley of the sun ever since. Our headlights weren’t in really bad shape, but once they start to degrade, it doesn’t get better.

Hazy area on upper right headlight cover
Left headlight is in worse shape

When this happened on our Alpine Coach, I polished the lens covers with a product from Meguiar’s. The problem was, the Meguiar’s polished out the haze, but it also removed any remaining UV inhibitor and within a year, the headlight covers were in worse shape than ever.

After looking around a bit, I found a product made by Sylvania that not only polishes out the imperfections, it includes a new clear lens coating with UV inhibitor! I ordered a kit from Amazon – it was only $19.99 – to give it a try.

Sylvania Headlight Restorer kit

The kit included detailed instructions – it’s broken down into three steps. First you clean the cover and spritz it with a liquid etching solution. Then you wet sand progressively with 400 grit, then 1000 grit and finally 2000 grit sand paper. I used a spray bottle to keep plenty of water on the acrylic cover while sanding with fairly light pressure. You sand until the surface is smooth with each grit. At this point, the headlights look really bad – they are completely clouded from sanding. After rinsing and drying, you apply the etch again, rinse and dry again, then apply the clear coat with the UV inhibitor. The results were amazing.

Restored right headlight
Left headlight after restoration

The whole process took about an hour. I’m pleased with the result. Now we’ll have to see how it holds up to exposure to sunlight.

Speaking of sunshine, we have plenty in the forecast. After having daily highs in the mid-60s all week, the forecast calls for 75 degrees today – and we’re well on our way there – and mid to upper 70s for the week ahead with clear skies.

*Just so you know, if you use this link to shop on Amazon and decide to purchase anything, you pay the same price as usual and  I’ll earn a few pennies for the referral. It’ll go into the beer fund. Thanks!

Our Transportation Evolution

When I closed my last post on Thursday, I mentioned our plan to go to the Power Food Park and meet up with friends. That’s what we did. We arrived around 5:30pm to find a much smaller crowd and fewer food trucks than were present on the Saturday before. Donna had reserved a fire pit and s’mores packets from 6pm to 8pm. We found Mike and Jodi Hall right away and staked out a picnic table.

We decided to go ahead and order food and eat at the picnic table before going to our reserved fire pit (number 6) where we had six Adirondack chairs around the fire pit. Frank and Kelly Burk joined us. We had a lot of laughs around the fire – the temperature drops fairly quickly after sundown and the fire pit made it very comfortable. Here are a couple of underexposed photos.

Kelly, Frank and Jodie at the fire pit
Mike Hall and Donna

It was a fun time and two hours was about right for yukking it up around the fire.

Friday morning I started the Traeger around 8am and put on a pork shoulder (Boston Butt). I didn’t play pickleball Friday, I was saving my legs for the Valentine’s Day tournament on Saturday. The plan was to make pulled pork and take it across the street to Chuck and Sue Lines’ place at 5pm. Roxy and Dick Zarowny would join us there. Sue made potato salad and Roxie made cole slaw and a cucumber salad and lime pie. I brought nearly five pounds of pulled pork and it made a great dinner. Again we had a great time talking into the night and Chuck had a propane fired fire pit!

Donna and I played in the Valentine’s tournament Saturday morning. It wasn’t really a tournament – it was a round-robin type scheduled play with players teamed up with their sweetheart and rotating play against other teams. We won 50% of our matches, but I don’t think we were playing at our best. It was fun nonetheless.

We drove to Frank and Kelly’s place in the afternoon – it’s only a couple of miles from where we used to live in east Mesa, about five miles from Viewpoint Golf and RV Resort. It was breezy out and felt chilly although the thermometer registered 69 degrees. We enjoyed cocktails and laughs, then Frank got serious on the grill. He had some super thick USDA Prime New York steaks and grilled them to perfection. Donna brought spinach and bacon stuffed mushrooms for an appetizer – they were delicious. Kelly made roasted asparagus and yellow squash and potato kisses for sides. It was a great meal and laughs continued at the dinner table.

We drove our new-to-us Nissan truck to the Burk’s place and I was glad we did. It started raining when we left around 9pm. I don’t like to drive the MG Midget at night, especially when it’s raining. It was no bother in the Nissan Frontier though.

Our modes of transportation have evolved over the years we’ve spent on the road. When we first left our sticks-and-bricks home for the full-time RV lifestyle, I thought having a scooter to get around would be sufficient. I figured we just needed something to go to the store occasionally and if we really needed a car we could rent one from time to time. We learned to pack away a surprising amount of groceries on our Kymco Downtown 300i scooter. It’s pictured on the header of the blog page.

It had limitations though. It was capable of carrying us on the freeway, but whipping along at 70mph with cars all around us wasn’t exactly comfortable. Also, with its small wheels, it wasn’t the best on dirt or gravel surfaces which we often found in and around RV parks.

After a couple of years, we traded it in for a Can-Am Spyder three-wheeled motorcycle. This was much more versatile, but again it wasn’t the most comfortable vehicle for longer trips and extended freeway driving. We tried to avoid rainy weather or didn’t drive much at night.

The MG Midget was the next step in the evolution of transportation for us. Midget-San with its Nissan A15 engine and five-speed transmission made freeway travel easy, but you have to be on your toes as the sports car is very low and small. Like riding a motorcycle, you always have the assume the other drivers don’t see you. For Donna, all of these choices compromised her hair style. She either had helmet head or wind blown hair from driving top-down in Midget-San.

Now we can take the Frontier without any of our previous limitations. Midget -San will be relegated to local jaunts when we feel like it. The Frontier will be more of a daily driver.

We took a drive on Sunday morning. I felt like getting out and Donna wanted to see how the Salt River and Saguaro Lake looked for kayaking. The Frontier will be great for transporting the Sea Eagle kayak to almost any drop-off point. We loaded the Sea Eagle in the Midget many times, but we tried to stay off of dirt roads or difficult launch areas.

To get to Saguaro Lake from east Mesa is an easy drive. We took Ellsworth Road over Usery Pass to Bush Highway. It’s only a few miles, but it’s night and day compared to town. Crossing Usery Pass dropped us into the Tonto National Forest – a forest of desert scrub and cactus. Saguaro Lake is a popular boating, kayaking and fishing spot. It has a marina with a restaurant and also the Desert Belle tour boat.

Saguaro Lake marina
View of the lake toward Butcher Jones Recreation Area

The Desert Belle cruise is a narrated tour of the lake and various sites and recreation areas. It has food and drink onboard, but currently only upper deck outdoor seating is open.

Desert Belle cruise boats

We back-tracked on Bush Highway and took a look at the Goldfield Salt River access point, but it didn’t look too good to get a kayak down to the river there. Next, we stopped at Phon D Sutton which has access and the water level is just enough to put a kayak in there. We stayed at Phon D Sutton several years ago when dry camping was allowed there – it’s the header photo – but you can’t stay overnight anymore.

Our last stop was at the Granite Reef Recreation Center. It was busy and we saw several kayakers there. With the low water levels, it seems like the stretch of water between Phon D Sutton and Granite Reef is the place to go.

It was a fun-filled weekend with good food, good friends and lots of laughs. We don’t have any real plans for the week ahead. The weather forecast calls for cooler weather with daily highs in the mid 60s until next weekend when it will warm up again.

*Just so you know, if you use this link to shop on Amazon and decide to purchase anything, you pay the same price as usual and  I’ll earn a few pennies for the referral. It’ll go into the beer fund. Thanks!

Donna’s Deals

I wrote about my decision-making process when I bought the Nissan Frontier truck. I’d decided on a simple work truck that was inexpensive and didn’t have a lot of bells and whistles to repair. I didn’t always have vehicles like this. In fact, for about 35 years, I always drove a current model-year car and rarely put over 6,000 miles on it before getting a new one.

This started about 40 years ago when I was the service manager at Herman Cook VW in Encinitas, California. My compensation package included a company car which was a new VW out of the dealership inventory they called a demonstrator (demo) vehicle. I usually drove a Volkswagen GTI back then. In 1984, I went to work for Volkswagen of America and again, as a manager, my compensation package included a company car.

In fact, it came with a car, gasoline and car washes at the company’s expense! I always drove a new car and turned them in every 6,000 miles or so. These cars would be sent to wholesale auction listed as “executive demo.” My position also included company lease car privileges. I could lease up to four vehicles at very favorable rates. The rate would be 1% to 1.5% of the MSRP. So, a $30,000 car would cost me three or four hundred per month and it included full coverage insurance. Unlike retail leases, there were no upfront fees, just the monthly rate.

This was such a deal that I leased a car for my wife and when my daughters got their drivers licenses, I leased cars for them. It was cheaper to put them in a new car every year than it would be to buy a used car when you factor in the cost of insurance and repairs. The lease program was a 12-month term, so they were always in a current model-year car with warranty coverage. While they were in school, I paid the lease for them. They’re adults now, but they still get a new lease car every year – I don’t think they’ve ever had to buy a car for themselves.

Volkswagen offers these programs to management level employees for the benefit of the employee, but it also helps them. When they send a 12-month old car or a 6,000-mile demo to the wholesale auction, they get a good price for it. This helps keep the wholesale residual value of the cars high – which, in turn, is used to set retail lease rates. Higher residual values mean lower retail lease rates. But I don’t drive new cars anymore – just my daughters do.

Donna’s been watching for deals on stuff for our new-to-us park model home. She found a deal on a stereo system for the Arizona room. It’s old school – a Kenwood KR4400 receiver that’s circa 1974, a Pioneer CD player and a set of Celestion D4 bookshelf speakers. There was a guy here at Viewpoint Golf and RV Resort selling the system. He was the original owner and bought this stuff when he was in high school. I was a senior in 1974, but I didn’t have the money for a stereo like this. It’s good stuff.

I’ve always been a fan of Celestion speakers. They don’t make consumer speaker cabinets anymore. The company, based in Britain, makes speakers for use in PA systems or for guitar amplifier cabinets. Building vacuum tube guitar amplifiers was once a hobby of mine. I always used Celestion speakers in my cabinets that I special ordered from an outfit in Idaho called Avatar speakers.

I built several guitar amplifiers – one was a clone of a Marshall 18-watt that was a blues monster. It had that fat Marshall sound and could be pushed into a creamy distortion without blowing out your eardrums.

Marshall 18-watt clone head and Avatar 2×12 cabinet

The amplifier was built with point-to-point wiring of all of the components. I enjoyed this work. You had to be meticulous, the wire lengths and pathways were important.

Marshall 18-watt clone board
Marshall 18-watt chassis and tube set

Another amp I built was based on the British Hiwatt design. This amp was loud and produced a very clean tone. It also powered an Avatar 2×12 cabinet with Celestion speakers.

Chassis and tube set

There was a fairly obscure amp designer and builder back in the day named Ken Fischer. He designed a line of amps called Trainwreck and custom-made them for star entertainers. Ken passed away in 2006, but his amps are still highly sought after. I read recently that Brad Paisley acquired one. His amp circuits are complex and everything has to be precisely placed to make it do the Trainwreck thing. The thing about them is, once you have this rig set up, you can change the sound of the guitar from a clean, almost sparkly tone to a growling distortion with small adjustments of the guitar volume knob. The amplifier is very sensitive to the input voltage from the guitar pickup.

I corresponded with a few guys that were trying to copy the Trainwreck design. I found a guy in Australia, an electrical engineer that was also a musician. He experimented with building a printed circuit board (PCB) that followed Ken Fischer’s original point-to-point design. I bought a board from him and built one. It’s fantastic and also plays very loud.

Trainwreck patterned printed circuit board
Trainwreck custom cabinet
Trainwreck chassis and tube set

I’ve been hauling the Marshall 18-watt and the Trainwreck amps in the basement of our Alpine Coach for nearly eight years. The Avatar 2×12 cabinet was lost when our trailer was stolen by those dirty, rotten thieves. I’ll have to get them out and clean them up after we move into the park model.

I was talking about deals Donna found before I got sidetracked. Donna found a small, 4.4 cubic-foot refrigerator for $75 – it cost $275 new and we bought it from the same couple that sold us the stereo. On Tuesday, Donna made a fantastic find. She was talking to our neighbor, Dean, when he mentioned another neighbor on the row behind us was selling a tow bar. I’d been looking at tow bars online – we’ll need one for the Nissan Frontier to tow it behind the coach. I was looking at the Roadmaster line, made in Vancouver, Washington. I toured their plant in 2014 and I think they have the best tow bars available.

We walked over to Jim and Gerry Jarvis’ site and what do you know – he had a Roadmaster Nighthawk tow bar with the Defender shield for sale. The Nighthawk is their top-of-the-line unit. It’s the Cadillac of tow bars. He bought it new in late 2018, used it to tow his Jeep to Oregon and back before he sold his motorhome and bought a fifth-wheel trailer.

A new Nighthawk is listed online for a price of $1140 and the Defender shield is $460. Jim sold me this $1600 set-up for just $500. Deal! Next month I’ll have a Roadmaster base plate installed on the truck and we’ll be good to go. That’ll cost about $1200, so I’ll be about $1700 into what’s about a $3,000 set-up!

The weather here in Mesa, Arizona continues to be pleasant with daily highs in the 70s and overnight lows in the 50s. We plan to go back to the Power Food Park tonight and meet up with our friends, Mike and Jodi Hall and Frank and Kelly Burk. We reserved a firepit from 6-8pm. Donna is playing in the 3.0 pickleball round robin tomorrow morning. And we’re signed up as a team for the Valentine’s pickleball tournament on Saturday.

*Just so you know, if you use this link to shop on Amazon and decide to purchase anything, you pay the same price as usual and  I’ll earn a few pennies for the referral. It’ll go into the beer fund. Thanks!